DieHard 20 Operator's Manual

CAUTION:Read and follow all Safety Rules and Operating Instructions Before Every Use of this Product.SAVE THESE INSTRUCTIONS.Sears, Roebuck and Co., H

• 8 •CHARGER FEATURES 10. ASSEMBLY INSTRUCTIONS11. It is important to fully assemble your charger before use. Follow these instructions for assembly:P

• 9 •TO ATTACH THE AXLE ASSEMBLY:Remove charger from packing materials and place upside down on a at 11.1 surface. Attach mounting foot and secure wi

• 10 •Place the charger on its side. Place one end of each bracket into slot, then 11.3 place the axle assembly under each bracket. Fasten the other s

• 11 •USING THE GFCI OUTLET12. This charger includes two – GFCI (Ground Fault Circuit Interrupter) outlets located on its back. The purpose of a GFCI

• 12 •6 VOLT when charging, testing or starting 6 volt systems.TOUCH-PAD CONTROLS13.3 With your charger connected to the vehicle and power source, the

• 13 •If you do not set a time, the charger will run for the maximum time. After selecting the charge rate and proper time, the charger will start cha

• 14 •(Engine Start) WAIT Wait until the charger is ready before cranking again FULL Battery is charged (Automatic mode) OFF Time has expired

• 15 •BATTERY SIZE/RATINGCHARGE RATE/ CHARGING TIME - HOURS2 AMP 20 AMP 60 AMPSMALL BATTERIESMotorcycle, gar-den, tractor, etc.6 - 12 AH 2 - 4 NR NR12

• 16 •will be charged to 100 percent needs another 50 percent (.50)).Multiply the Amp Hour rating by the charge needed (.50) and divide by • the charg

• 17 •Important:Do not try to start the engine without a battery in it. You could cause dam-age to the electrical system.If the engine does turn over,

TABLE OF CONTENTSSECTION PAGE1. IMPORTANT SAFETY INSTRUCTIONS X2. PRODUCT FEATURES X3. BEFORE USING X4. CONNECTING CABLE ASSEMBLY X5.

• 18 •TROUBLESHOOTING18. PROBLEM POSSIBLE CAUSE SOLUTION/REASONSNo reading on the am-meter.Clamps are not making a good connection.2-amp charge rate i

• 19 •WARRANTY19. THREE-YEAR FULL WARRANTYIf this Battery Charger fails due to a defect in material or workmanship within three years from the date of

• 20 •

• 21 •

• 22 •

• 1 •IMPORTANT SAFETY INSTRUCTIONS1. SAVE THESE INSTRUCTIONS – The DieHard model 71234 Manual Bat-1.1 tery Charger, offers a wide range of features to

• 2 •TURER AND MANUFACTURER OF ANY EQUIPMENT YOU INTEND TO USE IN VICINITY OF BATTERY. REVIEW CAUTIONARY MARKING ON THESE PRODUCTS AND ON ENGINE.PERSO

• 3 •facturer’s recharging instructions.Study all battery manufacturer’s specic precautions while charging and 3.5 recommended rates of charge.Determ

• 4 •For positive-grounded vehicle, connect NEGATIVE (BLACK) clip from bat-6.6 tery charger to NEGATIVE (NEG, N, –) ungrounded post of battery. Con-ne

• 5 •BATTERY CHARGING - AC CONNECTIONS8. For all grounded cord-connected battery chargers:8.1 GROUNDING AND AC POWER CORD CONNECTION • INSTRUCTIONS –

• 6 •Recommended minimum AWG size for extension cords for battery 8.3 chargers:25 50 100 150(7.6) (15.2) (30.5) (45.6)0 2 18 18 18 162 3 18 18 16 143

• 7 •PARTS9. The Sears service centers offer the following replacement parts for your battery charger. If you are having trouble with your battery cha